Well, my initial paper casting tests have already taught me a few
things.
- Soaking
and blending the cotton pulp for a longer time is better than a shorter
time.
I followed the
instructions on the cotton linters package, but the pulp turned out rather
lumpy and completely fell apart when I went to remove it from the mold. The next time, I soaked it longer and blended
it longer, and put in a teaspoonful of an additive that is supposed to
neutralize any acidity in the pulp (which is irrelevant, since the cotton is
not acidic), and make for a smoother surface.
This mixture worked much better, the texture was finer, it did indeed
have a smoother surface, and it held together when removed from the mold. It also seemed to dry a bit quicker.
 |
| Some rough cotton pulp castings |
2. Don’t use an unsealed plaster mold.
Since I don’t yet
have everything I need to make my first custom mold, I just used
some things I had on hand to do some tests.
One was a cast resin Celtic cross wall hanging. Another was a plaster plaque I’d made and
used to try out some carving techniques.
I sprayed both with a bit of cooking spray as a mold release. The resin
piece was roughly sculpted, but worked pretty well.
But the plaster piece, after the watery pulp
juice soaked into it, and I pressed down firmly with my sponge to remove as
much water as possible and get the pulp down into the nooks and crannies, ended
up falling apart as I removed the finished cast.
Many of the tutorials I’ve seen on paper casting use terra
cotta molds, which are fired. I imagine
that makes the difference.
 |
| Oops! |
3. WAIT until it’s dry to try to remove the
paper from the mold.
This is
challenging! A lesson in tempering my enthusiasm with patience.
4. Sizing
matters.
I don’t know why this didn’t occur to me
before, since I am well aware of the necessity of sizing substrates that are
going to be painted. Sizing is a
substance that reduces absorbency, so ink or paint doesn’t bleed or feather
into the surface.
Turns out those pure
cotton linters fibers are pretty damn absorbent! Considering cotton is used for wound
dressing and maxi pads, this should have been an obvious consideration. Perhaps it was because most of the paper
casting tutorials I’ve seen were not intended to be painted. Fine art applications of cast paper are often
left in their pure white state, so sizing wasn’t mentioned.
In any case, my attempt to apply a base coat
of acrylic paint to my unsized test castings resulted in the fibers soaking up
the moisture and swelling and basically ruining the integrity of the cast form.
My initial
research into possible sizing options have revealed that there are two basic
types: internal, which is dissolved into the wet pulp, and external, which is
applied to the surface after the paper has dried. I think internal would be easier and more
appropriate for what I’m doing. Possible
additives include white glue, gelatin and various starches. I’d rather not deal with food-based stuff,
since various critters consider them tasty and I’d like to avoid having my work
nibbled by moths or mice. And I already
have a ginormous gallon bottle of Elmer’s Glue sitting in the corner. Hopefully it hasn’t dried out into a solid
brick. I’ll start with that and see how
it goes.
UPDATE!
Since I started
this post a few days ago, I’ve been playing around with various mixtures of
pulp, glue and plaster. The mixtures
with the glue have not set up correctly.
But I don’t think I’ll need the glue.
Just Plaster of Paris and pulp seem to be giving me the lightness,
durability and harder, less absorbent surface that I need.
I realized that the pure pulp surface was too
soft to hold up to the multiple layers of finishing I want to do. But with the addition of plaster, the surface
takes detail well and can take paint and other finishes perfectly.
 |
| Plastic lid + broken earring + cotton pulp & plaster = ART SCIENCE!!! |
To test my various mixtures, I made some simple disc-shaped castings, using the plastic lid of a catnip container as a mold. Cat didn't mind. Unlike any time I pull out the sewing machine, Cat doesn't seem all that interested in this process.
The plaster/pulp mixtures set to the point of de-molding quite quickly (within a half our to an hour for these little discs). This is much shorter than for the pure pulp, which took several hours to a few days to dry to the point where it could be removed from the mold without risk of damage.
However, there is a fairly long curing time
for the pulp/plaster mixture. By curing I mean the piece is fully dried and hardened. Plaster is interesting because it hardens via
a chemical reaction, not through evaporation – and that chemical change creates
heat. So it gets warm as the chemical reaction takes place. But once the plaster has chemically set, the
water still needs to gas off, and the evaporation makes it cold to the touch. This is true of plaster in general, but I think the large amount of water in the pulp increases this curing time. While it's still cold, the plaster is still somewhat damp and delicate.
It's also somewhat malleable.
During this time, I can add subtle surface
texture by scratching and pressing with various tools, smooth and shape stuff and generally customize each casting fairly
easily, making each one truly unique.
Once it returns to room temp, it’s hard and sturdy and lightweight and
perfect. I can literally throw it on the
ground and it won’t break. :)
 |
| Testing surface finishes |
Another thing I’ve been testing out is Gilder’s Paste – a surface
finish consisting of metallic particles in a wax base. This stuff is similar to the more familiar
Rub-n-Buff, which comes in a tube.
Gilder’s Paste comes in a flat tin, which is much easier to work with, and
has a much wider selection of colors to choose from. It can be applied to almost any surface with
a fingertip or thinned and applied with a brush or other applicator. Colors can be mixed and blended, too. Once the wax has dried, it can be buffed with
a soft cloth to a lovely metallic sheen.
Very shiny!
I was all set to spend a chunk of Christmas gift cash (thanks, Mom!) on a selection of Gilders Paste colors after the holidays. But before I could place my order, I came across a box of art supplies I'd inherited from Dore's father, who passed away last year.
He was a craft enthusiast, mainly interested in stamping. He had a wide selection of stamp crafting supplies, many of which he'd gotten for free from the manufacturers because he wrote product reviews for various crafting magazines and websites. He mostly made cards, which he created by combining various stamps into a composition and then coloring the image with various paints and craft finishes. He loved lighthouses, and most of his pieces featured a lighthouse somewhere, even if it was peeking out behind a tree in the distance.
Lo and behold, as I excavated this box of treasures, what did I find but 20 tins of Gilders Paste! Pretty much every color I was planning on buying and more, each worth about $10. I feel like I got a special Christmas gift from beyond the Great Mystery. Thanks, Joe! :)
 |
| A Gift of Gilders Paste! |
So my plan is to base coat each piece with acrylic paints, then
highlight the raised areas with Gilders Paste metallic colors, and then add whatever
additional color embellishments seem appropriate. Then I'll seal the whole thing with a gloss varnish, which should make the finished pieces damn near bulletproof!
Next step is making my mold!
